Lobos-tech LB-FEA800M Manual de usuario

User Guide LB-FEA800M Rev.1.0 2005/1/27

8 LED Indicators There are three LED-Indicators (100M, LNK/ACT, FDX/COL) for each UTP port. The following table provides descripti

Off Half-duplex mode or no device attached. Table 2-1. The description of LED Indicator Rear Panel The Console port and 3-pr

10 2. Remove adhesive backing from your Rubber Feet. 3. Apply the Rubber Feet to each corner on the bottom of the Switch. These footpads can preven

3. Network Application This section provides you a few samples of network topology in which the Switch is used. In general, the LB-FEA800M is de

12 this switch is suitable for department user to connect to the corporate backbone. Figure 3-2 Segment Application You can use the LB-FEA800M to

4. Network Configuration This Section explains how to configure console management via a direct connection to the console port of the LB-FEA800M.

14 Baud Rate: 9600 bps Data Bits: 8 Parity: none Stop Bit: 1 Control flow: None Figure 4-2. The settings of communication parameters After yo

Main Menu There are five items for selected as follows. n Status and Counters: Show the status of the switch. n Switch Static Configuration: Co

16 You can press the key of Tab or Backspace to choose item, and press Enter key to select item. Port Status This page display every port status

Actions-> You can press the key of Tab or Backspace to choose action menu, and press Enter key to select item <Quit>: Exit the page of port

18 4-2-3. System Information System Description: Display the name of device type. MAC Address: The unique hardware address assigned by manufacturer.

Administration Configuration Device Information

20 IP Configuration User can configure the IP setting and fill in the new value. Actions-> <Edit>: Configure all items. Finished configu

Change Username Use this page; user can change web management user name. Change Password Use this page; user can change web management user pa

22 Port / Trunk Configuration This page can change every port status and configure trunk group. Press TAB key to change configure of per item. 1.

Port Mirroring Configuration The port mirroring is a method for monitor traffic in switched networks. Traffic through ports can be monitored by one

24 <Next page>: Go to next page to configure. VLAN Configuration VLAN Configure 1. PVID (Port VID): Set the port VLAN ID that will be as

Create a VLAN Group Create a VLAN and add tagged /untagged member ports to it. 1. VLAN Name: Type a name for the new VLAN. 2. VLAN ID: Type a

26 Actions-> <Quit>: Exit this page and return to previous menu. <Edit>: Configure all items. Finished configure press ESC to go back

1. There are 0~7 priority level can map to high or low queue. 2. High/Low Queue Service Ration H:L : User can select the ratio of high priority pa

1. Introduction The LB-FEA800M is compact desktop size switches that are ideal solutions for SOHO (Small Office or Home Office) network user. It p

28 4-3-6.MAC Address Configuration 4-3-6-1.Static MAC Address When you add a static MAC address, it remains in the switch's address table, rega

Add static MAC address 1.Press <Add> --> <Edit> key to add a static MAC address. 2.Enter the MAC address to and from which the port s

30 4-3-6-2.Filtering MAC Address Edit Filtering MAC address 1.Press <Edit> key to modify a static Filtering address. 2.Choose the MAC address

4-3-7.Misc Configuration 4-3-7-1.Port Security A port in security mode will be “locked” without permission of address learning. Only the incoming

32 1.Press <Edit> to enable or disable the port security. 2.Press Space key to choose enable / disable item. 3.Press ESC to go back action me

4-3-7-3.Broadcast Storm Filtering This page is configuring broadcast storm control, press <Edit> to configure the broadcast storm filter

34 4-3-7-4.Max bridge transmit delay bound Max bridge transmit delay bound: Limit the packets queuing time in switch. If enable, the packets queued

action menu line. <Save>: Save all configure value. <Quit>: Exit this page and return to previous menu. 4-4.Protocol Related Configura

36 4-4-1-2.System Configuration 1.You can view spanning tree information about the Root Bridge on the left. 2.On the right, user can setting ne

4-4-1-3.Perport Configuration 1.PortState: You can view spanning tree status about the switch for per port. 2.PathCost: Specifies the path cost of

2 n IEEE802 .1Q VLAN, GVRP supported n Support Class of Service n Broadcast Storm filter supported n Support Port Security n IEEE802.3ad Port tr

38 4-4-2.SNMP Use this page to define management stations as trap managers and to enter SNMP community strings. User can also define a name, location

1.System Name: Type a name to be used for the switch. 2.System Contact: Type the name of contact person or organization. 3.System Location: Type the

40 Actions-> <Add>: Create a community strings. <Edit>: Modify all items. Finished configure press ESC to go back action menu line.

Actions-> <Add>: Create a trap manager. <Edit>: Modify all items. Finished configure press ESC to go back action menu line. &l

42 complete the deleting operation. <Save>: Save all configure value. <Quit>: Exit this page and return to previous menu. 4-4-3.GVRP Th

4-4-4.LACP 4-4-4-1.Aggregator Setting 1.Group: Display the trunk group ID. 2.LACP: Press Space key to enable or disable LACP (Link Aggregation

44 Actions-> <Edit>: Configure all items. Finished configure press ESC to go back action menu line. <Save>: Save all configure valu

Actions-> <Edit>: Configure all items. Finished configure press ESC to go back action menu line. <Save>: Save all configure value.

46 Actions-> <Quit>: Exit this page and return to previous menu. <Previous Page>: Return to previous page to view. <Next page>:

4-6. X-modem Upgrade 1.Press X key to start upgrading for X-modem. 1. First, disconnect terminal and modify baud rate to 57600bps, then do the c

Filter Database Support port static MAC address lock, MAC Filter, Port Security Port Mirror Use this feature to analysis port traffic for this swi

48 5.Select "1K X-modem" of protocol and press "Send" button. 6.After successfully upgraded the new firmware, please modify b

5. Web-Based Management This section introduces the configuration and functions of the Web-based management of 8TP+ 1Fiber Management Switch seri

50 as above. 5-1. Web Management Home Overview (The image was captured from 8TP + 100FX) 1. Home Page. 5-2. Port status 1. port status State: D

User can see a single port counter as follows 5-3. Port Statistics 1. The following information provides a view of the current status

52 5-4. Administrator Those management functions include: IP address, Switch settings, Console port information, Port controls Link aggregation,

5-4-2. Switch Setting 5-4-2-1.Basic 1. Description: Display the name of device type. 2. MAC Address: The unique hardware address assigned by m

54 5-4-2-2.Advanced Miscellaneous Setting : MAC Address Age-out Time: Type the number of seconds that an inactive MAC address remains in the switch

. Priority Queue Service settings: First Come First Service: The sequence of packets sent is depend on arrive order. All High before Low: The high

56 Qos Policy: High Priority Levels: 0~7 priority level can map to high or low queue. When the VLAN Tag number of a frame is mapping the priority lev

No VLAN 802.1Q(Tag VLAN) without GVRP VLAN mode 802.1Q(Tag VLAN) with GVRP VLAN mode (Default) Port Based Also, three kind of typologies shown a

4 Rubber Feet RS-232 cable User Guide Figure 1-2. Package Contents Compare the contents of

58 Note: This Router supports IGMP protocol, but IGMP function has to be in enable mode, and the Router has to be the Queryer. 3. This topology

Note: Suggest VOD server set with Switch has smallest IP address. 4. All of Switch must be in Disable mode, When VOD server is set up for IGMP Que

60 5-4-4. Port Controls 1. This page can Change every port status State: User can disable or enable this port control Auto Negotiation: User

5-4-5. Trunking The Trunking provides a standardized means for exchanging information between Partner Systems on a link to allow their Link Aggre

62 with the lowest value has the highest priority and is selected as the active LACP. 1.Group ID: you can create a link aggregation across two or m

5-4-5-2. Aggregator Information When you are setting LACP aggregator, you can see relation information in here. 5-4-5-3. State Activity Ac

64 perform dynamic LACP trunking. A link has two passive LACP ports will not perform dynamic LACP trunking because both ports are waiting for and L

5-4-6. Filter Database 5-4-6-1. IGMP Snooping The 8TP+1Fiber Management Switch support IP multicast , you can enable IGMP protocol on web manageme

66 Message Description Query A message sent from the querier (IGMP router or switch) asking for a response from each host belonging to the multicast

3. Click Static MAC Addresses. In the MAC address box, enter the MAC address to and from which the port should permanently forward traffic, regardle

Ethernet Switching Technology supplied higher performance at costs lower than other solutions. Wider bandwidth, no congestion, and the reduction in

68 5-4-7. VLAN configuration A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast domain. It allows you to isolate network

Support Port-based VLANs (IEEE 802.1Q VLAN) Port-based Tagging rule VLAN is an IEEE 802.1Q specification standard. Therefore, it is possible to crea

70 5. From the Available ports box, select ports to add to the switch and click Add. 6. Click Apply 5-4-7-2. Port VID Configure port VID settings

port's configured VID . Ingress Filtering Rule 2: Drop Untagged Frame. 5-4-8. Spanning Tree The Spanning-Tree Protocol (STP) is a standardized

72 Prameter Description Priority You can change priority value, A value used to identify the root bridge. The bridge with the lowest value has the

Parameter Description Port Priority You can make it more or less likely to become the root port, the rage is 0-255,default setting is 128 the lowe

74 Roving Analysis State: Enable or disable the port mirror function. Mirror Ports: The ports you want to mirror. All mirror port traffic will be c

Name: Enter a name to be used for the switch. Location: Enter the location of the switch. Contact: Enter the name of a person or organization.

76 5-4-11.Security Manager 1. Use this page, user can change web management user name and password. User name: root Password: root 5-4-12.

* Executing TFTP software * Copy firmware update version image.bin to TFTP software directory. * In web management select administrator— TFTP update

6 Management Methods The LB-FEA800M series supports following management methods: n Console and Telnet Management n Web-based

78 page to restore the EEPROM value.

5-4-14. Reset System Reset Switch to default configuration, default value as below 5-4-15. Reboot Reboot the Switch in software reset.

80 6. Technical Specifications This section provides the specifications of the LB-FEA800M and the following table lists the specifications. Stan

Operational Temp. 0℃ ~ 50℃ Power Supply 100~240VAC, 50/60 Hz Power Consumption 15 Watts EMI & Safety FCC A, CE, UL, cUL

82 7. Troubleshooting This section is intended to help you solve the most common problems on the LB-FEA800M series. Incorrect connections

Diagnosing LED Indicators The Switch can be easily monitored through panel indicators to assist in identifying problems, which

2. Hardware Description This section mainly describes the hardware of the LB-FEA800M. Physical dimensions The physical dime